See more Easy Fit Door Sets
The Easy Fit door set is a door and frame, already cut and routered for hinges and latch, ensuring it is easy to fit with no joinery expertise or specialist tools. The hinges, latch and latch plate are included so all you need to do is fix it into the door opening and add a handle. You can replace your existing door quickly and easily, just measure your existing opening to determine which size you require.
- Save time and money and avoid the expense of hiring a joiner
- Pre-painted white - no further decoration required
- Door, frame kit, hinges & latch plate supplied - handles not included
Features and Benefits
The Easy Fit door range is an interior door system so simple anyone can fit in minutes without being an expert, or the need of a joiner. Suitable for most standard sized door openings.
- This door can be hung left or right handed so you choose which way it opens
- For opening sizes of (W)683-695mm (H)1988-1996mm (D)35mm
- To give you the flexibility to choose the style and finish you want, our doors are sold without handles
- Easy lift off hinges to swap or remove doors easily
- Includes door and frame kit, hinges, latch and latch plate - all you need are the handles
- Made from responsibly sourced, Forest Friendly timber
- This product is to be installed within an existing door frame, and is not suitable for new apertures
Health and Safety
Please note that this item has additional safety or regulatory datasheets available. The product may have possible health and safety hazards covered in these documents. Refer to the container for full information and always follow the instructions.
|Timber approval||FSC® approved|
|Comes with||Door, frame kit, hinges & latch plate supplied - handles not included|
|Fitting||This door can be hung left or right handed so you choose which way it opens|
very good idea
Anonymous - 3 years ago
the idea is very good but quality of screws are poor ,throw them away and buy good quality ones that are not made of butter then you will not have any problems with them bending and snapping and thats with pilot holes drilled. small amount of imperfections, dried glue on showing and a small knock but not worth sending back when a small problem can be over come. one other down is you will have to stay in all day , the tracking system does not work. but as i said the idea is very good and looks good in my building project
Biteme99 - 3 years ago
The side strip fell over and snapped in halF!!!!!!
Easy as eating chips
Anonymous - 3 years ago
I bought two as a test had to cut the bottom of both but save the bit you cut of and put it back in the bottom of the door with wood glue , it was so easy after that and they look perfect I have purchased 6 more
Mags75 - 3 years ago
I bought these a few weeks ago and my son put them in and said they were very easy to fit and were good value
Ronak77 - 4 years ago
Fitted this door in last week and one thing you need to be aware of is that your doorway will be narrowed by around 3 inches. The reason for this is that the means by which it has the hinge fittings and door knob fittings already fitted involves a side strip having to be fitted on the left and right of your door. On the left side strip the hinges are fitted and the right side is where the catch fits. The hinges are a specific design to work with this door.
As I used the door for a cupboard I did not mind the loss of 3 inches from the doorway but I would not use it for a room door.
I used wood glue when attaching the wood strips to the left and right of the doorway before screwing them down as it adds to the strength. I also used a few more screws than the instructions recommended for the same reasons.
I encountered a further complexity in that my door way was narrower at the bottom than the top and this meant I had to plane the right hand strip to ensure that the door fitted.
The door looks good and is prepainted but I plan to overcoat with eggshell. It is a strong door made of chipboard with plywood strips around it. Be careful when screwing into the strips or door as you can easily make a mark.
Overall if your doorway is a standard size then you will be able to fit the door in within 20 minutes with a screw driver. If not it will take a lot longer.