See more Midnight Granite Satin
12mm Midnight granite Black Laminate Upstand
Great for protecting the join between kitchen worktop and kitchen wall, this upstand from B&QMidnight granite range will match any midnight worktop, or compliment other styles in your kitchen. It's made from satin black granite effect laminate with a mdf base so it is stain and water resistant. It measures 70mm in height 3050mm in length and 12mm in thickness and is both an attractive and practical addition to your kitchen.
- Guarantee - 1 year
- Stain and water resistant
- Fixings not supplied
Features and Benefits
- For protecting the join between kitchen worktop and kitchen wall
- Made from responsibly sourced, Forest Friendly timber
|Timber approval||FSC® approved|
Bent and useless
Girlua - 1 year ago
These were so badly bent it has proved near impossible to fit.
aljan - 1 year ago
it work very well with the work tops i also brought
An excellent product.
Anonymous - 1 year ago
I took delivery of the item last weekend. It was very easy the cut the miters and install. It looks great and would recommend.
lovely finish bu a tendency to warp
halfpenny1 - 1 year ago
I bought four lengths of upstand two weeks ago to finish off my kitchen refurbishment. Having now completed the job, the upstands look great and really complement and improve the look of the worktops onto which they're fitted. However, fitting was another story. Despite storing the upstands flat on the floor for two weeks, when cut to the required length they all tended to warp outwards on each end for the final foot (30 cm)or so. I found the only way to effectively fix them to the wall therefore was as follows:
1. having cut the upstand to required length, lay it flat on the floor and apply two continuous beads of' No Nails' or similar instant grab mastic along the entire length of the lower and upper back of the upstand (ie the surface to be fitted against the wall), then a bead of clear silicone mastic along the bottom of it (ie the surface that will be in contact with the worktop).
2. Immediately place the section into position, pressing it firmly both against the wall and down onto the worktop at the same time. Working along it's entire length, ensure that you get as close and tight a fix as possible but, however good and level your wall surface is, you'll find it coming away in places and at one or both ends.
3. To overcome this problem, I pushed the upstand hard against the wall in those sections that were loose, and then pushed a stack of heavy books against it to hold it in place. On the ends where the worktop was open ended, I placed a small G clamp onto the worktop (using the slight overhang) with it tight up against the upstand ( I used a piece of cardboard too between g clamp and worktop/upstand to ensure a tight fit and to avoid possible damage to surfaces by the clamp). Behind the sink, I used a piece of wood and some spacers jammed tightly between the sink unit back edge and the upstand to force it tight to the wall
4. On corners, where you have cut a 45 degree mitre in the upstands in order to join two pieces, you'll find that the two adjoining sections tend to hold themselves in place on the ends so try to fit two or more sections at a time (as per stages 1 and 2 above) as the mastic beads will stay workable on the back/bottom of the upstand for at least 10-15 minutes).
5. Leave all clamps and weights in places for at least three hours to allow the mastic to set and hey presto you're done. Finally, run a very narrow bead of clear mastic between worktop and upstand joints, along the entire length and smooth off gently with a wet finger for a permanent waterproof seal. I can supply photos of my finished results if required.
phillip 101 - 2 years ago
this matches the worktop perfectly and give the worktop a nice clean finish
Customers who bought this also browsed
12mm Arlington Laminate Upstand
Great for protecting the join between worktop and wall, this upstand from B&QArlington range will give a great finishing touch to your kitchen. It's made from matt oak effect laminate with a mdf base so it is incredibly sturdy and hardwearing. It measures 70mm in height 3000mm in length and ...
12mm Designer White Laminate Upstand
Great for protecting your walls from splashes and for keeping your kitchen clean and hygienic, this upstand from Cooke & LewisDesigner range will give a great finishing touch to your kitchen. It's made from white laminate so it is abrasion and scratch resistant. It measures 70mm in height 3000mm in ...
12mm Star Black Acrylic Upstand
Great for protecting the join between kitchen worktop and kitchen wall, this upstand from EarthstoneStar range will give a great finishing touch to your kitchen. It's made from gloss black acrylic with a mdf base so it is resistant to mould, bacteria and most household stains. It measures 50mm in ...
15mm Aura Black Plastic Kitchen Upstand, Square edge
Great for protecting your walls from splashes and for keeping your kitchen clean and hygienic, this upstand from Aura range will give a great finishing touch to your kitchen. It's made from gloss black plastic with a mdf base so it is heat, water, moisture, steam, stain, impact and abrasion ...