See more Laminate Flooring
Colours Staccato Natural Oak parquet effect Laminate flooring, 1.86m² Pack
Unit of measure
Our stores do not stock this product
This laminate flooring has an attractive Oak parquet effect finish, embossed surface finish and bevelled edge. Each plank uses a simple click system, so installation is simple and it can be used with underfloor heating to keep your home warm.
- Suitable for all type of rooms (bathrooms when using hydro kit & pe foam) including living rooms, hallways, bedrooms, studies, utility rooms & kitchens
- Fitting type: Angle click system
- Water resistant
- Suitable for use with underfloor heating
- 20 years guarantee
Features and benefits
This laminate flooring has an attractive Oak parquet effect finish, embossed surface and bevelled edge. Each plank uses a simple click system, so installation is simple. It can be used with underfloor heating to keep your home warm.
- Suitable for all type of rooms, including bathrooms when using hydrokit & PE foam.
- Made from responsibly sourced, Forest Friendly timber
Health and safety
Please note that this item has additional safety or regulatory datasheets available. The product may have possible health and safety hazards covered in these documents. Refer to the container for full information and always follow the instructions.
|Effect||Oak parquet effect|
|Material||High density fibreboard (HDF)|
|Base material||High density fibreboard (HDF)|
|Underlay type required||Foam underlay|
Awful flooring DO NOT BUY
moic33 - 3 days ago
I am a professional floor fitter and my customer bought this flooring. This has to be the worst flooring I have laid. Due to the width of the boards there is no give in the manipulation of the board to assist with locking in under tight conditions. Doorways are difficult with this flooring and due to the boards having two tongue edges there is no way to lock in the board after the first run. I had to shave the shorter tongue off every single board and then use the longer edge to lock in the boards. Will never recommend and clearly a manufacturing issue. STAY AWAY. I will NOT be fitting this board again.
Hard work but worth it
JDMK - 22 days ago
Definitely a 2 or 3 person job to lay since an entire room width must be pushed with all your might and weight as you push it into place. It is machined with very fine tolerances so check each piece for dust and vacuum between laying each row as the slightest bit of dust will make it hard to get a good fit. It really is physical work to push it hard enough but once you get the hang of it, the click of it falling into place is satisfying. Have an off cut ready to bang with a hammer to push any pieces that don't behave into position. Takes careful measuring if your room is wonky so take your time to get the first row perfect as all subsequent rows will be pushed into it. Change the blade on your saw - need 2 blades per room. Me (mum) and adult daughter laid one room over two long afternoons and are really pleased with the result. Plus another 2 hours to do the trim.
Great product but always arrives damaged
dandoeslaminate - 1 month ago
Bought this flooring and it looks great, but out of 19 packs 7 were damaged, store stock is also damaged. Agreed a partial refund with B&Q but 2 months later they still have not paid, a joke to deal with! On fitting, put each run in at once, click each panel together and then lift them all in.
Leerut1972 - 2 months ago
Bought this 10 months ago. Considering it’s laminate you can’t tell once it’s down. Doesn’t move when you walk it on it, very solid feel and hasn’t scuffed at all after 10 months. I don’t fit flooring for a living but was sceptical when buying due to some reviews stating it’s a nightmare to fit. I had no problems whatsoever. You do though need the correct tools to do the fitting. Going to buy some more for my bedroom it’s that good
Fridgeman01 - 3 months ago
Bought this product as it was exactly what we was looking for and it was not cheap, Im extremly DIY experianced and can turn my hand to anything and have laid laminate floor many times before in the bast. This product was by far the WORST I have had to fit, it would just not click together completely, Trust me this is a PIG to fit and this was going back to the suppler with some strong words behind it until I read these views and saw someone had cut the lip off on the side of the panel to get it to fit. Once I did this it fitted like a dream and I soon had it down BUT given what this costs etc I don't see why you should have to cut this off to be able to get it to fit.
once its down it look great, my advise would be that if this design is not the one and only one you want then don't buy it, if it is beware that you need to cut the R/H/S lip off each panel. Good Luck!!